JRangelp Welding Electrode Holder 300AMP Heave-Duty Jaw Holding Pliers Copper Electrode Clamp Stick Electrode Welding Pliers

JRangelp Welding Electrode Holder 300AMP Heave-Duty Jaw Holding Pliers Copper Electrode Clamp Stick Electrode Welding Pliers for MIG/ARC Welding Machine

$12.99 @ Amazon.com

☑High Standard☑ This electric welding clamp is made of high-quality copper material, and the one-piece forging process of pure copper is strong and durable, and it is not easy to rust. In addition, the grip is made of non-slip material, not easy to slip, convenient and practical

☑Stable Jaw☑ This welding electrode holder supports multi-angle clamping, such as 48°, 90°, 180°. In addition, the clamping mouth adopts a special diamond-shaped clamping mouth design, which has high occlusal strength, and the welding rod is not easy to fall off, which greatly improves work efficiency.

☑Widely Applications☑ This welding clamping is used for welding table legs, railings, pipes and more. Furthermore, it is suitable for most 300A arc, MMA, handheld welding operations and suitable for various rod-shaped electrodes of 2.5-3.2mm, etc.

☑Easy to Install☑ First unscrew the screw, remove the upper part, then connect the wire, and finally push the copper sheet into the handle to use

Heat insulation block, heat insulation conduction handle

JRangelp Welding Electrode Holder 300AMP Heave-Duty Jaw Holding Pliers Copper Electrode Clamp Stick Electrode Welding Pliers for MIG/ARC Welding Machine

Electrode Holder 500 Amp Welding Electrode Holder Set, Heavy Duty Jaw Holding Plier Electrode Clamp for Arc MMA Welder,Black

$21.99 @ Amazon.com

【High Quality Welding Electrode Holder】The upper and lower clamps of the electrode clamp are made of high copper alloy for maximum conductivity and strength. High quality electrode holder with 500A current capacity, comfortable insulated handle, convenient and easy to operate. Ideal for most arc, MMA, hand welding work.

【Heat-resistant insulation for Safety】The handle is molded from a durable glass-filled nylon material for good heat and impact resistance. Glass-filled nylon handle and clamp insulated for maximum operator protection and safety.

【Groove Jaw Design】The grooved jaw for firm grip of rods in 45°, 90°, 135°, 180° positions. Clamping Device holds the stick electrode tight so it will not slip while welding and transfers the welding current to the stick electrode.

【Welding Chipping Hammer & Wire Scratch Brush】Welding chip hammer is made of high strength and toughness steel. Dual-headed design, one end is flat chisel, the other end is pointed chisel, convenient operation in narrow space.Coil spring handles reduce vibration and improve comfort. The wire brush is made of stainless steel bristles and with wooden handle, they are durable and have a strong cleaning ability.

【Work Great】Which are easy to remove and clean corrosion and slag from most of your welds, Welding chipping hammer and steel wire brush, makes it easy to clean and remove slag from all your welds. The welding hammer is a durable tool for long strokes. It can also be used as a life hammer and broken ice hammer.

Electrode Holder 500 Amp Welding Electrode Holder Set, Heavy Duty Jaw Holding Plier Electrode Clamp for Arc MMA Welder,Black

YESWELDER Welding Electrode Holder 300Amp for SMAW(MMA) Stick Electrode Jaw Holding Plier Copper Electrode Clamp for Welding Machine ARC Welder

$13.99 @ Amazon.com

MAXIMUM AMPERAGE-Suitable for up to 300A

EXCELLENT QUALITY-High conductivity and improved cable connection, which is more secure and easy to replace.

COMFORTABLE OPERATION-Great for most Arc, MMA, Hand Stick welding jobs. Easy to operate with newly designed level for good hand clearance and better hold.

SAFETY DESIGN-Heat resistant handle, made of arc-resistant insulation and impact resistant material.

[METHOD APPLICATION] This 300A welding electrode holder connects to the welding cable and conducts the welding current to the electrode. The insulated handle is used to guide the electrode over the weld joint and feed the electrode over the weld joint and feed the electrode into the weld puddle as it is consumed.

YESWELDER Welding Electrode Holder 300Amp for SMAW(MMA) Stick Electrode Jaw Holding Plier Copper Electrode Clamp for Welding Machine ARC Welder

Welding Electrode Holder Cuwiny 300AMP High Quality Copper Electrode Clamp Jaw Holding Plier Fit for ARC Welder Welding Machine Stick Electrode Welding American Design

$15.19 @ Amazon.com

This Electrode holder is Made of high quality Copper materials for high conductivity and improved cable connections. Supplied with an allen wrench and cable connection ferrule, assuring efficient connnection and minimizing cable strand breakage at the connection. (New product promotion, only this week. Reviews and feedback, contact us for 20% off.)

Used # 1 AWG Gauge Cable and High-quality Copper.

Fit for Arc Welder 200A 300AMP etc,Suit for various kinds of Stick Welding Rods Electrodes etc.

The high temperature/high impact-resistant molded fiberglass fully insulated body to protect against electrical shock and have powerful spring loaded non-slip insulated clamping jaws to hold the electrode tight so it will not slip while welding.

Satisfactory after-sales service:Cuwiny products have 1 Year after-sales customers service guarantee.Please contact us for any assistance.

Welding Electrode Holder Cuwiny 300AMP High Quality Copper Electrode Clamp Jaw Holding Plier Fit for ARC Welder Welding Machine Stick Electrode Welding American Design

Reboot Welding Electrode Holder 300AMP Copper Heavy Duty Jaw Holding Plier Electrode Clamp of Welding Machine ARC Welder American Design

$14.99 @ Amazon.com

🛒Large 300Amp welding electrode holder provides durability, 1/4~7/8 inch electrode capacity.

🛒Used # 1 AWG Gauge Cable

🛒Applicable to use with MMA ARC Welders 200 300 Amp, Suit for various kinds of Stick Welding Rods Electrodes etc.

🛒Electrode holder is made of High Quality Brass material with Insulated Handle. Special Design for Easy Cable Connection with Free Spanner and Spacing Sheet

🛒100% Customer Satisfaction Guarantee:All products from Reboot have 1 Year's after-sales customers service guarantee.Please contact us for any assistance.

Reboot Welding Electrode Holder 300AMP Copper Heavy Duty Jaw Holding Plier Electrode Clamp of Welding Machine ARC Welder American Design

Stick Electrode Holder, 800A Heavy Duty Jaw Design Welder Holding Clamp with Non-slip Handle, Welding Rod holder Plier for Welding Machine

$22.57 @ Amazon.com (Save 7%)

800A WELDING ELECTRODE HOLDER: Pure copper thickened one-piece molding, good electrical conductivity, heating up quickly and not hot hands, long time welding does not get hot.

PRISMATIC JAWS: Prismatic design of brass jaws, high bite strength welding rod is not easy to fall off, to ensure a firm grip without slipping, but also to ensure the safety of work.

INSULATED HANDLE: The handle is made of special insulating and heat-resistant materials, anti-scalding and high temperature resistance. The whole body is non-conductive, suitable for long working hours.

COMFORTABLE GRIP: Ergonomic design, the curvature of the handle more closely fits the curve of the palm, non-slip texture, comfortable hand grip, long working hours without tired hands.

SCOPE OF APPLICATION: Suitable for a variety of work environments, pipe welding, mechanical maintenance, site welding a variety of scenarios applicable, simple operation, safe and durable.

Stick Electrode Holder, 800A Heavy Duty Jaw Design Welder Holding Clamp with Non-slip Handle, Welding Rod holder Plier for Welding Machine

SSIMDER Welding Electrode Holder Lead ARC Welding Ground Clamp and Welding Cable Stick Electrode Holder Welding Plier Clamp Stinger Copper Jaw Holding Plier for 10-800A Welder Machine

$39.99 @ Amazon.com

✔【★Upgraded Welding Electrode Holder and Cable】SSIMDER Welding Electrode Holder Lead Assembly manufactured with 25mm² Highly Flexible Cable.The cable diameter is 0.418 inch.Suitable for both high and low current 10-800A electrode MMA ARC welding machines, suitable for various electrode electrodes, etc.

✔【★ Full length 9.8FT Welding Cable with Clamp】Constructed with Welding Pure Copper Highly Flexible Stranding Cable Wire and Heavy Duty Nylon Body ,Stick/Arc Welding 600 Amp Electrode Holder With Long Cable is total 9.8ft.Equipped with 9.8ft Welding Electrode Ground Clamp to meet most Welding Requirements.Diameter 9mm/0.35 inch plug DKJ 10-25 Dinse Quick Connector,convenient and efficient.You will receive a ready to use fully assembled lead, no Tool Accessories required.

✔【★600A Welding Plier】Upgraded Welding Jaw Holding Plier is made of High Quality Brass material with Ergonomic Handle. The high temperature/high impact-resistant molded fully insulated body to protect against electrical shock, not easy to oxidize with heat, strong bite force.And the Welding Electrode Rod holder have powerful spring loaded non-slip insulated clamping jaws to hold the electrode tight so Welding Electrode Holder will not slip while welding.

✔【★Copper Welding Ground Clamp】This Welder Copper Plier Ground Clamp uses a copper chuck with strong current.Large hex screw cable connection assures a tight and safe cable connection. Welder Ground Wire Pliers has a large contact area for an effective ground connection. Welder ground clamp and cable design eliminates arc blowing and facilitates fast grounding spot changing.High temperature resistance, suitable for long-term use.

✔【★Professional Manufacturer】SSIMDER is a professional welding machine,welding equipment & accessories manufacturer, we aim to provide a better welding tools and welder accessories, such as Welding Electrode Holder, Welding Plier,Welding Ground Clamp,Welding Cable and make welding easier. If you have any questions, feel free to contact us.

SSIMDER Welding Electrode Holder Lead ARC Welding Ground Clamp and Welding Cable Stick Electrode Holder Welding Plier Clamp Stinger Copper Jaw Holding Plier for 10-800A Welder Machine

800 Amp Welding Electrode Holder Clamp Welding Rod Plier for Stick Electrode Holder for Holding and Welding with Welding Machine

$23.39 @ Amazon.com

Safe Working-Brass clamping mouth with jaw design guarantees firm holding without slipping, and safe working as well.

High Resistant Temperatures-This Stick Electrode Holder adopts insulating and heat‑resistant materials, the electrode clamp is resistant to high temperatures.

For Long Working Hour-The whole body of this electrode holder is non‑electrical conductive, suits perfectly for long working hour.

Easy Operation-This Stick Electrode Holder has a small size, a light weight and a non-slip handle, the operation is easier and more convenient.

Not Easy to Deform-Premium material and sturdy structure add more durability in long-term using, not easy to deform.

800 Amp Welding Electrode Holder Clamp Welding Rod Plier for Stick Electrode Holder for Holding and Welding with Welding Machine

Reboot Welding Electrode Holder, 400AMP Full Copper Heavy Duty Jaw Holding Plier Electrode Clamp of Welding Machine ARC Welder Stick Electrode Welding Machine

$21.49 @ Amazon.com

[High Conductivity and Stable Performance]: Heavy duty holding plier electrode clamp is made of high quality brass material which has good electrical conductivity and low resistance, with insulated handle; Electrodes burn within 1inch from the head and can be bent to any angle and still be held securely

[Pure Copper Nozzle]: Pure copper material of electrode holder is used around the nozzle, which has good electrical conductivity and low resistance; High temperature resistance,fire pro tection,longer service life; Size: 21 * 6.5 * 2.5cm / 8.3 * 2.6 * 1inch

[Comfortable to Hold]: The handle of welding electrode holder is light and compact reducing worker fatigue; welding electrode stick has a great feel and gripping space; Welding electrode holder is 400-500A universal, welding accessories is easy and convenient to use

[Stable and Firm Grip]: The embedded clamp is solid the welding rod is directly embedded, stable and not easy to fall off. copper one forged and durable, and the heat is concentrated on the head. Long-term welding is not hot and durable

[with Insulated Handle]: Electrode holder is made of high quality brass material with insulated handle. special design for easy cable connection with free spanner and spacing sheet; welding electrode holder suit for various kinds of stick welding rods electrodes

Reboot Welding Electrode Holder, 400AMP Full Copper Heavy Duty Jaw Holding Plier Electrode Clamp of Welding Machine ARC Welder Stick Electrode Welding Machine

KSEIBI 331215 300 Amp Welding Electrode Holder American Design

$14.83 @ Amazon.com

This Electrode holder is Made from high quality materials for high conductivity and improved cable connections. Supplied with an allen wrench and cable connection ferrule, assuring efficient connnection and minimizing cable strand breakage at the connection.

Large 300-Amp provides durability, up to 5/32" inch electrode capacity.

Lightweight and easy to operate with newly designed level for good hand clearance and better hold.

The high temperature / high impact-resistant molded fiberglass fully insulated body to protect against electrical shock and have powerful spring loaded non-slip insulated clamping jaws to hold the electrode tight so it will not slip while welding.

Use KSEIBI electrode holder to connect to the welding cable and con-duct the welding current to the electrode.

KSEIBI 331215 300 Amp Welding Electrode Holder American Design